View B170UW01V1_6946880.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

au optronics corporation b170uw01 v1 product specification document version 1.1 1/36 ( ) preliminary specifications ( v ) final specifications module 17.0? wuxga color tft-lcd model name b170uw01 v1 customer date checked & approved by note: this specification is subject to change witho ut notice. approved by date beyond yang may 28, 2007 prepared by amy tu may 28, 2007 mdbu marketing division / au optronics corporation www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 2/36 contents 1. handling precautions............................ ................................................... ............................... 4 2. general description............................. ................................................... ................................. 5 2.1 general specification.......................... ................................................... ............................ 5 2.2 optical characteristics ........................ ................................................... ............................ 6 3. functional block diagram ........................ ................................................... ......................... 11 4. absolute maximum ratings........................ ................................................... ....................... 12 4.1 absolute ratings of tft lcd module ............. ................................................... ............. 12 4.2 absolute ratings of backlight unit ............. ................................................... ................... 12 5. electrical characteristics ...................... ................................................... ............................. 13 5.1 tft lcd module ................................. ................................................... ......................... 13 5.2 backlight unit................................. ................................................... ............................... 15 6. signal characteristic ........................... ................................................... ............................... 17 6.1 pixel format image............................. ................................................... .......................... 17 6.2 the input data format.......................... ................................................... .......................... 18 6.3 signal description/pin assignment .............. ................................................... ................. 20 6.4 interface timing ............................... ................................................... ............................. 22 7. connector description ........................... ................................................... ............................ 25 7.1 tft lcd module ................................. ................................................... ......................... 25 7.2 backlight unit................................. ................................................... ............................... 25 7.3 signal for lamp connector...................... ................................................... ...................... 25 8. reliability..................................... ................................................... ........................................ 26 9. mechanical characteristics ...................... ................................................... ......................... 28 9.1 lcm outline dimension.......................... ................................................... ...................... 28 9.2 screw hole depth and center position ........... ................................................... ............. 30 10. shipping and package ........................... ................................................... .......................... 31 10.1 shipping label format......................... ................................................... ....................... 31 10.2. carton package ............................... ................................................... .......................... 32 11.3 shipping package of palletizing............... ................................................... .................... 32 11. appendix: edid description ..................... ................................................... ....................... 33 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 3/36 record of revision version and date page old description new description remark 0.1 2007/02/26 all initialize the preliminary speci fication 1.0 2007/05/21 all finalize the specification 1.1 2007/05/28 31 add driver ic 2 nd source www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 4/36 1. handling precautions 1) since front polarizer is easily damaged, pay att ention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact wi th water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with a bsorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break o r crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the ccfl re flector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal inter face connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration th at no bending/twisting forces are applied to the tft module from outside. otherwise t he tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammabilit y grade is used in the lcd module. the lcd module should be supplied by power complied wit h requirements of limited power source (iec60950 or ul1950), or be applied exemptio n. 14) the lcd module is designed so that the ccfl in it is supplied by limited current circuit (iec60950 or ul1950). do not connect the ccfl in ha zardous voltage circuit. www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 5/36 2. general description b170uw01 v0 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wuxga (1920(h) x 1200(v)) screen and 262k colors (r gb 6-bits data driver). all input signals are lvds interface compatible. inverter of backlight is not included. b170uw01 v0 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 431.8 active area [mm] 367.20(h) x 229.50(v) pixels h x v 1920 x 3(rgb) x 1200 pixel pitch [mm] 0. 191 (per one triad) x 0. 191 pixel arrangement r,g,b vertical stripe display mode normally white white luminance (i ccfl =6.5ma) note: i ccfl is lamp current [cd/m 2 ] 200 min. / 240 typ. (5 points average) (note1) luminance uniformity 1.25 max. (5 points average) 1.8 max. (13 points average) contrast ratio 500 min. / 600 typ. optical rise time/fall time [msec] 8 typ. / 12 max. nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 3.0 max (without b/l) 10.0 max (with b/l) weight (without inverter) [grams] 650 typ., 680g max. physical size [mm] 382.7 max.(w) x 244.8 max.(h) x 6.6 max. (t) electrical interface 6bit, 2 channels lvds surface treatment anti-glare support color native 262k colors(rgb 6-bit data) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 6/36 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature): item unit conditions min. typ. max. note white luminance i ccfl =6.5ma [cd/m 2 ] 5 points average 200 240 - 1, 4, 5. [degree] [degree] horizontal (right) cr = 10 (left) 60 60 70 70 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) 40 50 60 60 - - 9 luminance uniformity 5 points - - 1.25 1 luminance uniformity 13 points - - 1.8 2 cr: contrast ratio 500 600 - 6 cross talk % - - 4 7 [msec] rising - - - [msec] falling - - - response time [msec] rising + falling - 8 12 8 red x 0.560 0.580 0.600 red y 0.320 0.340 0.360 green x 0.290 0.310 0.330 green y 0.530 0.550 0.570 blue x 0.135 0.155 0.175 blue y 0.135 0.155 0.175 white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 2,9 ntsc ratio % cie 1931 42 45 - www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 7/36 note 1: 5 points position (display area: 367.20 (h) x 229.50 (v) mm) 1 2 3 4 5 h /4 h /4 h /4 h /4 h w w /4 w /4 w /4 w /4 note 2: 13 points position w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance value s by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 8/36 note 4: measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature ch ange during measuring. in order to stabilize the luminan ce, the measurement should be executed after lighti ng backlight for 30 minutes in a stable, windless and dark room. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. center of the screen tft - lcd module 50 cm photo detector lcd panel field=2 contrast ratio (cr) = brightness on the ?white? state brightness on the ?black? state www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 9/36 note 7 definition of cross talk (ct) ct = | y b ? y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8: definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from ?black? to ?white? (falling time) and from ?white? to ?black? (rising time), respectively. the response time inte rval between the 10% and 90% of amplitudes. refer to figure as b elow. "black" tr tf "white" "white" 0 % 10 % 90 % 100 % optical response www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 10/36 note 9: definition of viewing angle viewing angle is the measurement of contrast ratio 10, at the screen center, over a 180 horizontal an d R 180 vertical range (off-normal viewing angles). th e 180 viewing angle range is broken down as follow s; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measureme nt direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 11/36 3. functional block diagram the following diagram shows the functional block of the 17.0 inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1920(r/g/b) x 3 1200 gnd dc-dc converter ref circuit y-driver x-driver odd_ rxin0 odd_rxin1 odd_rxin2 odd_rxclkin (8 pairs lvds) jae fi-xb30sl-hf10 or compatible mating housing jae fi-x30h jst bhsr-02vs-1 lamp connector(2pin) even_ rxin0 even_rxin1 even_rxin2 even_rxclkin www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 12/36 4. absolute maximum ratings absolute maximum rating of the module is as followi ng: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 6.5 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: with in ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis(incoming inspection standard). twb=39c operating range storage range -20 60 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 13/36 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - 2.5 3 [watt] note 1 idd idd current - 750 - [ma] note 1 i rush inrush current - - tbd [ma] note 2 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p vddns allowable logic/lcd drive ripple noise - - 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 measure condition q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (lcd module input) (high to low) control signal r2 1k r2 1k r1 47k +3.3v 90% 10% vin rising 0v 3.3v 0.5ms www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 14/36 5.1.2 signal electrical characteristics input signals shall be low or hi-z state when vdd i s off. it is recommended to refer the specifications of th c63lvdf84a(thine electronics inc.) in detail. signal electrical characteristics are as fo llows: parameter condition min max unit vth differential input high threshold (vcm=+1.2v) - 350 [mv] vtl differential input low threshold (vcm=+1.2v) -350 - [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds differential voltage www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 15/36 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition ccfl current(i ccfl ) 3.0 6.5 7.0 [ma] rms (ta=25 ) note 2 ccfl frequency(f ccfl ) 40 50 80 [khz] (ta=25 ) note 3,4 ccfl ignition voltage(vs) - 1210 1450 [volt] rms (ta= 0 ) note 5 ccfl ignition voltage(vs) - 1010 1210 [volt] rms (ta= 25 ) note 5 ccfl voltage (reference) (v ccfl ) 666 740 814 [volt] rms (ta=25 ) note 6 ccfl power consumption (p ccfl ) - 4.81 - [watt] (ta=25 ) note 6 note 1: the below are auo recommended design points . *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to che ck safety circuit very carefully. impedance of ccfl , for instance, becomes more than 1 [m ohm] when ccfl is damaged. *4 generally, ccfl has some amount of delay time af ter applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 ccfl discharge frequency must be carefully chose n so as not to produce interfering noise stripes on the screen. *6 reducing ccfl current increases ccfl discharge v oltage and generally increases ccfl discharge frequency. all the parameters of an inverter should be carefully designed, so as not to produce too mu ch leakage current from high-voltage output of the inv erter. note 2: it should be employed the inverter which ha s ?duty dimming?, if iccfl is less than 4ma. note 3: ccfl discharge frequency should be carefull y determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. note 5: ccfl inverter should be able to give out a power that has a generating capacity of over 1480 voltage. lamp units need 1450 voltage minimum for ignition. www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 16/36 note 6: calculator value for reference (i ccfl v ccfl =p ccfl ) note 7: requirements for a system inverter design, which is intended to have a better display performa nce, a better power efficiency and a more reliable lamp, a re following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform shou ld be less than 10%. b. the distortion rate of the waveform should be wi thin 2 10%. * inverter output waveform had better be more simil ar to ideal sine wave. www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 17/36 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 2 1919 1920 1st line 1200th line www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 18/36 6.2 the input data format odd pair( 1st pixel input) g0 r5 r4 r3 r2 r1 r0 de vs hs b5 b4 b3 b2 b1 b0 g5 g4 g3 g2 g1 ck din1 din2 din3 even pair(2nd pixel input) g0 r5 r4 r3 r2 r1 r0 de vs hs b5 b4 b3 b2 b1 b0 g5 g4 g3 g2 g1 ck din1 din2 din3 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 19/36 signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of thes e 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the typical frequency is 48.2 mhz. the signal is us ed to strobe the pixel data and dsptmg signals. all pixel data shall be valid at the falling edge when the dsptmg signal is high. de display timing this signal is strobed at the falling edge of -dtclk. when the signal is high, the pixel data sha ll be valid to be displayed. vs vertical sync the signal is synchronized to -dtclk . hs horizontal sync the signal is synchronized to -dtclk . note: output signals from any system shall be low o r high-z state when vdd is off. www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 20/36 6.3 signal description/pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin no symbol function etc. 1 gnd ground 2 vdd power supply ,3.3 v (typical) 3 vdd power supply ,3.3 v (typical) 4 v edid ddc 3.3v power 5 nc no connection (reserved for auo) test 6 clk edid ddc clock 7 data edid ddc data 8 odd_rxin0- -lvds differential data input 9 odd_rxin0+ +lvds differential data input 10 gnd ground 11 odd_rxin1- -lvds differential data input 12 odd_rxin1+ +lvds differential data input 13 gnd ground 14 odd_rxin2- -lvds differential data input 15 odd_rxin2+ +lvds differential data input 16 gnd ground 17 odd_rxclkin- -lvds differential clock input 18 odd_rxclkin+ +lvds differential clock input 19 gnd ground 20 even_rxin0- -lvds differential data input 21 even_rxin0+ +lvds differential data input 22 gnd ground 23 even_rxin1- -lvds differential data input 24 even_rxin1+ +lvds differential data input 25 gnd ground 26 even_rxin2- -lvds differential data input 27 even_rxin2+ +lvds differential data input 28 gnd ground 29 even_rxclkin- -lvds differential clock input 30 even_rxclkin+ +lvds differential clock input www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 21/36 note1: start from right side note2: please follow vesa standard. note3: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r lvds receiver signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 22/36 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1920 x 1200 / 60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock tbd 78.75 tbd mhz period t v 1208 1250 2048 active t vd - 1200 - vertical section blanking t vb 8 50 848 t line period t h 1000 1050 2048 active t hd - 960 - horizontal section blanking t hb 40 90 1088 t clock note : de mode only www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 23/36 6.4.2 timing diagram 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 24/36 power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 25/36 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer jae or compatible type / part number fi-xb30sl-hf10 or compatible mating housing/part number fi-x30h mating contact/part number fi-xc3-1-15000 7.2 backlight unit physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 26/36 8. reliability items required conditions operating life ? high temp. temp.= +50 c, dynamic. 250 hours, room humidity operating life ? low temp. temp.= 0 c, dynamic, 250 hours, room humidity high temp. storage life ? non-operating temp.= +60 c, non-operating, 250 hours , humidity 20% low temp. storage life ? non-operating temp.= -20 c, non-operating, 250 hours, room humidty high temp. & high humidity operating life temp.=+40 c,dynamic,humidity 95%(non- condensing), 250 hours shock ? non-operating 180g, 2.0 ms, half sine wave vibration ? non-operating random vibration, 1.5g zero-to- peak, 10 to 500hz, 30min. in each of three mutually perpendicular axes temp. cycle ? non-operating -20 c to +60 c, duration at temp. = 30min, test cycles = 50 esd contact : 8kv/ operation air : 15kv / operation www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 27/36 note 1: a failure is defined as the appearance of p ixel failure on any color layer or the appearance o f horizontal or vertical lines, bars etc. note 2: low temperature storage ?panel must return to operating temperature range prior to activation. ? note 3: hi temperature / humidity test max. wet-bulb temperature is less than 39 o c; at glass temperature high than 40 o c. temperature and relative humidity range is shown in the figure below. twb=39c operating range storage range -20 60 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 28/36 9. mechanical characteristics 9.1 lcm outline dimension www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 29/36 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 30/36 9.2 screw hole depth and center position screw hole minimum depth, from side surface =2.6 mm (see drawing) screw hole center location, from front surface = 3. 75 0.2mm (see drawing) screw maximum length = 2.3 mm (see drawing) screw torque: maximum2.5 kgzf-cm www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 31/36 10. shipping and package 10.1 shipping label format h/w f/w remark xx x 0a 1 nec driver ic 1a 1 novatek driver ic 23m h/w: 1a f/w: 1 1 axxg www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 32/36 10.2. carton package 11.3 shipping package of palletizing www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 33/36 11. appendix: edid description address function value value value note hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code 88 10001000 136 0b hex, lsb first 11 00010001 17 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 11 00010001 17 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 25 00100101 37 16 max v image size (rounded to cm) 17 00010111 23 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) 07 00000111 7 1a blue/white low bits (lower 2:2:2:2 bits) e5 11100101 229 1b red x (upper 8 bits) 97 10010111 151 1c red y/ higher 8 bits 57 01010111 87 1d green x 4f 01001111 79 1e green y 8c 10001100 140 1f blue x 27 00100111 39 20 blue y 22 00100010 34 21 white x 50 01010000 80 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 34/36 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 54 01010100 84 37 pixel clock/10000 usb 3d 00111101 61 38 horz active lower 8bits 80 10000000 128 39 horz blanking lower 8bits a0 10100000 160 3a horzact:horzblnk upper 4:4 bits 70 01110000 112 3b vertical active lower 8bits b0 10110000 176 3c vertical blanking lower 8bits 17 00010111 23 3d vert act : vertical blanking (upper 4:4 bit) 40 01000000 64 3e horzsync. offset 30 00110000 48 3f horzsync.width 20 00100000 32 40 vertsync.offset : vertsync.width 36 00110110 54 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits 6f 01101111 111 43 vertical image size lower 8bits e5 11100101 229 44 horizontal & vertical image size (upper 4:4 bits) 10 00010000 16 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 35/36 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 a 60 manufacture 55 01010101 85 u 61 manufacture 4f 01001111 79 o 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 www..net
au optronics corporation b170uw01 v1 product specification document version 1.1 36/36 70 00 00000000 0 71 manufacture p/n 42 01000010 66 b 72 manufacture p/n 31 00110001 49 1 73 manufacture p/n 37 00110111 55 7 74 manufacture p/n 30 00110000 48 0 75 manufacture p/n 55 01010101 85 u 76 manufacture p/n 57 01010111 87 w 77 manufacture p/n 30 00110000 48 0 78 manufacture p/n 31 00110001 49 1 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 v 7b manufacture p/n 31 00110001 49 1 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum 96 10010110 150 www..net

▲Up To Search▲

Price & Availability of B170UW01V1

	To Download B170UW01V1 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .